FREE HELP~FREE HELP~FREE HELP ~FREE HELP~FREEFREE HELP

WHICH BELLOWS DOES FIT MY BOAT?

STARTING WITH THE OUTER  TRANSOM PLATE

THERE ARE THREE BELLOWS IN THE OUTER TRANSOM PLATE THE LARGEST FITS AROUND THE UNIVERSAL JOINTS AND ENGINE YOKE.

THERE ARE FOUR POSSIBLE BELLOWS

1) THE NON RIDGE IM362

USED PRIOR TO THE 1971 WHICH HAS A FLAT INNER FLANGE WHERE IT

     MOUNTS ON THE TRANSOM PLATE AND BELL HOUSING  THE SURFACE

WHERE THE BELLOWS SEATS HAS RIVITS AROUND IT AND THE HEADS DIG

INTO THE BELLOWS ONDER THE CLAMP SO IT WILL NOT SLIP OFF

2) THE RIDGE IM511

USED AFTER TO THE 1971 WHICH HAS A FLAT INNER FLANGE WITH A BEAD

    OR RIDGE WHERE IT MOUNTS ON THE TRANSOM PLATE AND BELL HOUSING

THIS RIDGE SNAPS INTO A GROVE CUT INTO THE FLANGE SO IT WILL NOT SLIP

OFF WHEN CLAMPED ABOVE THE BEAD WITH EXTERNAL WORM CLAMPS.

3) THE GEN II IM515

USED AFTER TO THE 1992 WHICH HAS A FLAT INNER FLANGE WITH A BEAD

    OR RIDGE WHERE IT MOUNTS ON THE TRANSOM PLATE AND BELL HOUSING

THIS RIDGE SNAPS INTO A GROVE CUT INTO THE FLANGE SO IT WILL NOT SLIP

OFF WHEN CLAMPED ABOVE THE BEAD WITH EXTERNAL WORM CLAMP ON

THE FORWARD END.  THE REAR END FOR THE BELL HOUSING HAS AN

ALUMINUM BAND WHICH HOLDS IT INTO THE BELL INTERNALLY.  IT

HAS AN EXTERNAL RIDGE WITH ONE RIDGE WHICH MATES WITH THE BELL

HOUSING.

4) THE BRAVO IM514

USED AFTER TO THE 1988 WHICH HAS A FLAT INNER FLANGE WITH A BEAD

    OR RIDGE WHERE IT MOUNTS ON THE TRANSOM PLATE AND BELL HOUSING

THIS RIDGE SNAPS INTO A GROVE CUT INTO THE FLANGE SO IT WILL NOT SLIP

OFF WHEN CLAMPED ABOVE THE BEAD WITH EXTERNAL WORM CLAMP ON

THE FORWARD END.

 THE REAR END FOR THE BELL HOUSING HAS AN

ALUMINUM BAND WHICH HOLDS IT INTO THE BELL INTERNALLY.  IT

HAS AN EXTERNAL RIDGE WITH TWO LARGE BEADS WHICH MATES WITH THE

BELL HOUSING. THE DOUBLE BEAD MARKS IT AS DIFFERENT FROM THE

GEN II BELLOWS WITH ONLY ONE BEAD.

 

OF THE THREE BELLOWS IN THE OUTER TRANSOM PLATE THE SECOND

LARGEST IS TO TRANSFER THE EXHAUST FROM TRANSOM THROUGH THE

PROP ONLY TWO BELLOWS ARE POSSIBLE

1) THE ONE END IM501

OF THE TWO BELLOWS  POSSIBLE  THIS IS HARDLY USED. IT WAS

STANDARD ONLY ONE YEAR AS EXHAUST RELIEF ATTEMPT BECAUSE

IT OPENED UP WHEN TRIMMED UP.  ITS FAILURE AND REMOVAL

WAS DUE TO THE NOISE AND SOOT ON THE WHOLE REAR OF THE BOAT.

SOME BOOTS WHEN THEY COME TO SERVICE HAS THIS BELLOWS INSTALLED

IN A YEAR WHERE THEY WERE NOY ORIGINAL BECAUSE THE OWNER HAD

TROUBLE INSTALLING THE IM500 BELLOWS BELOW.

2) THE STANDARD IM500

OF THE TWO BELLOWS  POSSIBLE  THIS IS MOSTLY USED. IT WAS

STANDARD ALL EXCEPT ONE YEAR AS EXHAUST BELLOWS.

THIS IS IN ALL STANDARD TRANSOM REPAIR KITS.  TO MAKE IT

EASIER TO INSTALL IT IS SOMETIME STREACHED OVER A PLASTIC PIPE,

OR SOAKED IN HOT WATER TO SOFTEN IT PRIOR TO MOUNTING.

 

OF THE THREE BELLOWS IN THE OUTER TRANSOM PLATE THE SMALLEST

IS USED TO SEAL THE HOLE WHERE THE SHIFT CABLE GOES THROUGH THE

PLATE.  IT IS THE SAME FOR ALL MODELS

THE STANDARD IM504

THESE ARE USED IN COMBINATION OF THE EXHAUST AND UNIVERSAL

BELLOWS TO MAKE THE REPAIR KITS.

 

INTERNAL EXHAUST CONNECTORS FOR THE MANIFOLD PARTS

THE 165/140 INLINE BELLOWS IM502

THE 4" X 4" BELLOWS IM512

THE 4" X 3" BELLOWS IM503

INTERNAL EXHAUST TUBE CONNECTORS

THE 3" X 3" BELLOWS IM509

THE 4" X 4" BENT BELLOWS IM513

 

REPAIR KITS TO FIX THESE BELLOWS

 

MERCRUISER BELLOWS AND KITS

#1 AND ALPHA GEN I

Part Number:IM511

Uiversal Joint #1 Or Alpha #1

Part Number:IM511C

Uiversal Joint #1 Or Alpha #1 BELLOWS

PLUS EXHAUST AND SHIFT BELLOWS

Part Number:IM1000

Transom Plate Repair Kit

Part Number:IM1000D

Transom Plate Repair Kit W/SHIFT SEAL

Part Number:IM1832S

A-Uiversal Joint #1 Or Alpha #1

EVERYTHING REPAIR KIT

TRANSOM REPAIR KIT, YOKE REPAIR KIT WITH

U/J BEARINGS AND SEALS, PLUS LOWER SHIFT CABLE

ALPHA GEN II

Part Number:IM515

Uiversal Joint BELLOWS ALPHA  II

Part Number:IM515C

Uiversal Joint #1 Or Alpha #1 BELLOWS

PLUS EXHAUST AND SHIFT BELLOWS

Part Number:IM1002

Transom Plate Repair Kit

Part Number:IM1832S-2

A-Uiversal Joint GEN II

EVERYTHING REPAIR KIT

TRANSOM REPAIR KIT, YOKE REPAIR KIT WITH

U/J BEARINGS AND SEALS, PLUS LOWER SHIFT CABLE

BEAVO

Part Number:IM514

Uiversal Joint BELLOWS BRAVO

Part Number:IM514C

Uiversal Joint BRAVO BELLOWS

PLUS EXHAUST AND SHIFT BELLOWS

Part Number:IM1000B

Transom Plate Repair Kit BRAVO

Part Number:IM1832S-B

A-Uiversal Joint BRAVO

EVERYTHING REPAIR KIT

TRANSOM REPAIR KIT, YOKE REPAIR KIT WITH

U/J BEARINGS AND SEALS, PLUS LOWER SHIFT CABLE

#1 AND ALPHA GEN PRIOR 1972

Part Number:IM362

Uiversal Joint #1 NR

Part Number:IM511C

Uiversal Joint #1 Or Alpha #1 BELLOWS

PLUS EXHAUST AND SHIFT BELLOWS

Part Number:IM1000

Transom Plate Repair KitNR

Part Number:IM1832S

A-Uiversal Joint #1 Or Alpha #1

EVERYTHING REPAIR KIT

TRANSOM REPAIR KIT, YOKE REPAIR KIT WITH

U/J BEARINGS AND SEALS, PLUS LOWER SHIFT CABLE

 

INDIVIDUAL BELLOWS OTHER THEN U-JOINT

Part Number: IM500

Exhaust Bellows

(Outside Transom Plate)Transom plate exhaust bellows. List $30.95Replaces Mercruiser #32734

Fits #1 Plates 1970-1985 and earlier

Fits Alpha PLates 1986-1992

Fits Gen II and Bravo Plates

 

Part Number: IM501

 

ONE END OPEN EXHAUST BELLOWS

REPLACES IM500

BUT NOISE AND SOOT INCREASED ON THE BOAT REAR

Part Number: IM504

Shift Cable Bellows

Outside transom plate cable bellows.Replaces Mercruiser #74639

 

INDIVIDUAL BELLOWS INSIDE 

EXHAUST CONNECTOR

Part Number: IM512

4" X 4" Exhaust Tube

ELBOW TO EXHAUST TUBE

4" ELBOWS

Part Number: IM503

4" x 3" Inside Exhaust

ELBOW TO EX TUBE 3" ELBOW

Inside exhaust bellows for many V-8 and 4 cyl. Mercruiser.Replaces Mercruiser part #70981.

 

Part Number: IM509

Exhaust Tube Connector Bellows 3" X 3"

Used in exhaust systems with two piece exhaust tubes.Replaces Mercruiser part #90949.

 

 

Part Number: IM502

Exhaust Bellows 140/165

Inside Exhaust Bellows for 181/250 c.i.d. Mercruiser.Connects Exhaust Elbow To Exhaust Tube. List $70.95

Replaces Mercruiser Part #53114

Fits in line 4 & 6 Cyl engines

Does not fit early 120 h.p.

 

Part Number: IM513

Inside Tube Connector 4" X 4" (Bent)

Used for two piece inside exhaust tubes, CENTER CONNECTOR .Replaces Mercruiser part #14358

 

(800) 349-2628 ... (504) 888-2798 ... Fax (504) 888-2881
E-Mail to: (dmarine@rodnreel.com)

Same Day Local, National or International Shipping * Visa, Mastercard & Discover

UPS Next Day, 2nd Day, 3 day or Ground.

AfterMarket Home Page || Louisiana Fishing

AfterMarket Home Page: http//www.rodnreel.com/dmarine

Last updated March 24, 2011

PLEASE VISIT

MAIN SITE

ALTERNATORS

IGNITION

SEALS

PICTURED SITE

FUEL TANKS

MANIFOLDS

SHAFTS

1800FIXBOAT

BELLOWS

OMC VOL

SHIFT CABLE

I-O-PARTS.COM

COOLING

OUT DRIVE

STARTERS

 

GEARS

PUMPS

STEERING

AFTERMARKET

TRIM PUMPS ALL

MARINE ENGINES

OUTBOARD PARTS

MANIFOLD.COM

 

O/B PARTS

TRIM /TILT LINE

HOT WATER HEATER

HOT WATER SYSTEM COMPARISON

HOVERLOON

 

 ******